MetaTek

User Tools

Site Tools

You are here: start » ge » heaters
Trace:
ge:heaters

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
ge:heaters [2024/01/25 21:08] – Alan Sheage:heaters [2024/05/29 23:54] (current) – [Generator Anti-Condensation Heater] Alan Shea
Line 14: Line 14:
  
 <WRAP center round alert 60%> <WRAP center round alert 60%>
-**//DANGER//:** Starting a generator that has insulation resistance less than 1 Meg-ohm and with a voltage regulator connected **can cause a short circuit in the windings** resulting in permanent damage in less than one second, even without a load connected. +**//DANGER//:** Starting a generator that has insulation resistance less than 5 Meg-ohm and with a voltage regulator connected **can cause a short circuit in the windings** resulting in permanent damage in less than one second, even without a load connected. 
 </WRAP> </WRAP>
  
 Factory-supplied anti-condensation heaters operate at approximately 110C+ but are often mounted on a bracket in front of the exciter. They depend on the heat conduction through the bracket to the generator frame. This does not seem to keep the actual windings warm enough to prevent moisture accumulation in the winding insulation. ((Gensets built to spec provide an opportunity to order the generator with extra insulation treatment of the  windings("tropicalization"), which helps resist insulation breakdown caused by moisture absorption.  )) Factory-supplied anti-condensation heaters operate at approximately 110C+ but are often mounted on a bracket in front of the exciter. They depend on the heat conduction through the bracket to the generator frame. This does not seem to keep the actual windings warm enough to prevent moisture accumulation in the winding insulation. ((Gensets built to spec provide an opportunity to order the generator with extra insulation treatment of the  windings("tropicalization"), which helps resist insulation breakdown caused by moisture absorption.  ))
  
-We had tried using regulated heat tape, but the heat output decreases with temperature, and at 100F the output is below 1W/foot -- providing less than 25 watts total output. +We tried using regulated heat tape, but the heat output decreases with temperature, and at 100F the output is below 1W/foot -- providing less than 25 watts total output. 
  
 =====Clothes Iron Heater Solution=== =====Clothes Iron Heater Solution===
 {{ gen_heater.jpeg?direct&400 |}} {{ gen_heater.jpeg?direct&400 |}}
   * Strip the base plate from two 1000W / 230VAC clothes irons   * Strip the base plate from two 1000W / 230VAC clothes irons
-  * Drill & bolt the bases to each side of the generator mounting foot/frame +  * Drill & bolt the bases to each side of the generator mounting foot/frame -- avoid the heating element.  
-  * Connect in series to 230VAC. +  * Connect both irons in series and then to 230VAC. 
   * If possible, save the indicator light from the iron and mount it so that it is visible when power is connected to the heater to confirm proper operation.    * If possible, save the indicator light from the iron and mount it so that it is visible when power is connected to the heater to confirm proper operation. 
  
 +{{ :ge:generator_heaters_2.png?200|}}
 Operating at half voltage reduces power to 25% Operating at half voltage reduces power to 25%
   * Two 1000W irons in series @ 240V = 500W total, 250W each.    * Two 1000W irons in series @ 240V = 500W total, 250W each. 
ge/heaters.1706216914.txt.gz · Last modified: 2024/01/25 21:08 by Alan Shea

Page Tools

Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
CC Attribution-Share Alike 4.0 International Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki