MetaTek

User Tools

Site Tools

You are here: start » cp
Trace:
cp:start

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
cp:start [2024/05/30 00:01] – [Teco PLC SG2 Programming Source Code] Alan Sheacp:start [Unknown date] (current) – external edit (Unknown date) 127.0.0.1
Line 2: Line 2:
 {{ :cp:c61-genset-control-tower-3p.jpg?401|}} {{ :cp:c61-genset-control-tower-3p.jpg?401|}}
  
-The unified control system uses ComAp [[http://comap.cz/products/detail/intelicompact-nt-mint/|InteliCompact]] series generator controllers. [**//Replaced with [[https://www.comap-control.com/products/gen-set-paralleling-controllers/inteligen/inteligen-200 |InteliGen 200]] Controller//**] These controllers allow full control of all generator functions in a non-proprietary architecture. The system can control basic gensets (all sensors etc direct wired) or communicate with many computer controlled gensets directly through a CAN network. (Note: Some gensets with built in proprietary controls will not interface with the ComAp products--contact [[http://www.comapllc.com|ComAp]] for specific information).+The unified control system uses ComAp [[http://comap.cz/products/detail/intelicompact-nt-mint/|InteliCompact]] series generator controllers. [**//Replaced with [[hhttps://www.comap-control.com/products/controllers/paralleling-gen-set-controllers/inteligen/inteligen4-200/|InteliGen4 200]] Controller//**] These controllers allow full control of all generator functions in a non-proprietary architecture. The system can control basic gensets (all sensors etc direct wired) or communicate with many computer controlled gensets directly through a CAN network. (Note: Some gensets with built in proprietary controls will not interface with the ComAp products--contact [[http://www.comap.cz|ComAp]] for specific information).
  
-The system also uses a [[http://comap.cz/products/detail/mainscompact-nt/|MainsCompact]] to interface with local utility or an auxiliary power source -- for instance, a portable generator used for extremely low usage times. [**//Replaced with [[https://www.comap-control.com/products/switchgear-controllers/mains-controllers/intelimains-210 |InteliMains 210]]//**]+The system also uses a [[http://comap.cz/products/detail/mainscompact-nt/|MainsCompact]] to interface with local utility or an auxiliary power source -- for instance, a portable generator used for extremely low usage times. [**//Replaced with [[hhttps://www.comap-control.com/products/switchgear-control-and-protections/mains-controllers/intelimains-210-g2/|InteliMains 210 G2]]//**]
  
 The system is capable of running any one source, or all sources paralleled together at once. It can start, run, and stop generators from a remote location (such as a surgery building or operating room), or automatically as the load fluctuates. It also will monitor fuel levels and alarms and provide audible and visual warning of needed service.  The system is capable of running any one source, or all sources paralleled together at once. It can start, run, and stop generators from a remote location (such as a surgery building or operating room), or automatically as the load fluctuates. It also will monitor fuel levels and alarms and provide audible and visual warning of needed service. 
Line 14: Line 14:
 However, if an application plans to use proprietary gensets (such as Cummins PowerCommand), and does not need the paralleling function, a simple switch panel can replace the entire control tower in the overall design.  However, if an application plans to use proprietary gensets (such as Cummins PowerCommand), and does not need the paralleling function, a simple switch panel can replace the entire control tower in the overall design. 
  
-Contact [[:reference:Martin Energy]] as the preferred supplier for the control system. It can be assembled and tested along with the generators before shipping. {{ :cp:img_5133.jpg?300|Control Panel as built by Martin Energy Group}} [[Martin Control Panel Pictures]]+Contact [[:reference:Martin Energy]] as the preferred supplier for the control system. It can be assembled and tested along with the generators before shipping. {{ :cp:img_5133.jpg?300|Control Panel as built by Martin Energy Group}} [[cp-pictures]]
  
 For very detailed and in-depth information on generator paralleling systems, see [[http://cumminspower.com/www/en/technical/application/t-016.pdf|Cummins Power Paralleling Application Manual]] (PDF) and other useful Application Manuals at http://cumminspower.com/en/technical/application/index.jsp.  For very detailed and in-depth information on generator paralleling systems, see [[http://cumminspower.com/www/en/technical/application/t-016.pdf|Cummins Power Paralleling Application Manual]] (PDF) and other useful Application Manuals at http://cumminspower.com/en/technical/application/index.jsp. 
Line 20: Line 20:
  
 \\  \\ 
-<wrap center round alert 60%>+<wrap center round alert 250px>
 ** See Warnings below  ** ** See Warnings below  **
 </wrap> </wrap>
cp/start.1717027294.txt.gz · Last modified: 2024/05/30 00:01 by Alan Shea

Page Tools

Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
CC Attribution-Share Alike 4.0 International Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki

Copyright © Alan Shea, 2011-2025